Skip to content
Industrial combustion components support@rifuze.com

Azbil

Azbil ECM3000G9100 Electric control motor

Azbil ECM3000G9100 · view 1
Model
ECM3000G9100

Technical Specifications

MassApprox. 3 kg
ModelECM3000G9100
MaterialCase: die-cast aluminium. Cover: polycarbonate resin with GF. Bracket: steel.
ProtectionIP54 or equivalent
ApplicationsApplied to burner control, hot or cold water and steam valve control and general industrial process positioning, where the 90-degree stroke type suits burner air damper applications and the 160-degree type suits valve control, replacing older Azbil control motors.
Input signal4 to 20 mA DC
Key featuresDecoded from the official type summary as the ECM3000G91 base: 85 to 264 V AC wide-range power supply, 4 to 20 mA DC input signal, 90-degree angular stroke, with no optional auxiliary switches and not GB-compliant.; Output torque 12.5 N·m; motor timing approximately 39 s for 90 degrees of travel at no load; power consumption 14 W during operation.; Position-proportional operation with zero point, span and dead band adjustable; direct/reverse operation switchable, factory set to direct action.; Splash-proof structure IP54 or equivalent; die-cast aluminum case with polycarbonate resin cover and steel bracket; weight approximately 3 kg.; Feedback potentiometer with nominal value 135 Ω (combined resistance) and maximum applied voltage 5 V DC; repeatability less than ±3 %.; Ambient operating conditions -20 to +60 °C and 5 to 95 %RH without condensation; vibration resistance 4.9 m/s².; Standard bracket accessory allows retrofitting of older Azbil motors; compatible with Azbil controllers such as the SDC35/36, SDC45/46 and SDC40 series and DMC10.
Motor timingapprox. 39 s (no load)
Output torque12.5 N·m
RepeatabilityLess than ±3 %
Angular stroke90°
Operation modePosition proportional (direct/reverse operation switchable, zero point / span / deadband adjustable; factory-set to direct operation)
Operation typeTerminals 1-2: NO; terminals 1-3: NC
Optional partsCrank arm N-3128; damper arm J-26026G-ARM; valve linkage Q455C/D; damper linkage Q605A/D/E; base kit 83165292-001 for the V51E butterfly valve; waterproof connector 83104346-003; 24 V AC power supply transformer AT72-J1; extension units 83174065-002 / -102 (4 switches, 100 mA to 5 A) and 83174065-003 / -103 (4 switches, 1 to 100 mA); auxiliary potentiometer 83165272-001 (90° type) / -002 (160° type)
Product statusDiscontinued
Input impedanceEquivalent of 125 Ω or less at 20 mA (receiving resistance 45 Ω plus the resistance of the overcurrent protection circuit)
Ambient humidity5 to 95 %RH (no condensation allowed)
Product categoryIndustrial automation component - Electric control motor (rotary actuator for burner and valve control)
Storage humidity5 to 95 %RH (no condensation allowed)
Operating voltage85 to 264 V AC, 50/60 Hz
Power consumption14 W
Auxiliary switchesNone - the 11th digit is 0, i.e. "without options". An extension unit carrying four auxiliary switches (83174065-002 / -102 for 100 mA to 5 A, 83174065-003 / -103 for 1 to 100 mA) can be mounted on such a model; note *3 of the selection guide confirms this and adds that only one type of extension unit can be fitted.
Standard accessoryMounting bracket for replacing Azbil's older control motors - included as a standard accessory part
Ambient temperature-20 to +60 °C
Dielectric strength1500 V AC for 60 s between the power supply terminals and casing and between the input terminals and casing (85-264 V AC type); 1500 V AC for 60 s between the auxiliary switch terminals and casing
Replacement targetsAzbil's older control motors M904, M744 and M7284 can be replaced directly; terminals S, CONT, CW and CCW must then be wired with non-voltage contacts - never apply 24 V AC to them or the circuits may burn out
Storage temperature-20 to +70 °C
Vibration resistance4.9 m/s² in operation; 19.6 m/s² in transport/storage (packaged condition)
Insulation resistance5 MΩ or more by 500 V DC megger between the power supply terminals and casing and between the input terminals and casing; 20 MΩ or more between the auxiliary switch terminals and casing
Feedback potentiometerNominal 135 Ω (combined resistance 1 kΩ + 180 Ω), 0.5 W
Settable opening range5 to 95 % (must remain inside the end-switch range)
Auxiliary switch ratingNot applicable to this variant because no auxiliary switch is built in (11th digit 0). If an extension unit is fitted: standard type 250 V AC, 100 mA to 5 A resistive load and 100 mA to 3 A inductive load; low-current type 250 V AC, 1 to 100 mA inductive load including inrush current; if UL or CE compliance is required the rating is 30 Vrms or 42.4 V AC.
Factory switch positionsFor 90° angular stroke motors with built-in auxiliary switch, at factory settings: Close to Open (A, C) 9° ±5°; Open to Close (B, D) 81° ±5°
Potentiometer max voltage5 V DC
Auxiliary switch service lifeNot applicable to this variant (no built-in switch). Extension-unit switches follow the standard type (50,000 cycles or more) or the low-current type (200,000 cycles or more) figures.

Get a quote

Azbil · ECM3000G9100

Rotates a damper, valve or similar mechanical load through a fixed 90-degree angular stroke in proportion to a 4 to 20 mA DC control signal, converting a controller output into precise rotary positioning for industrial equipment such as burner air dampers.

Rotary actuator: purchasing checks

Review these fields for the complete ordering code. Unconfirmed fields can be included with your enquiry.

Operating voltage
85 to 264 V AC, 50/60 Hz
Torque
To be confirmed for the exact model
Travel angle
To be confirmed for the exact model
Running time
To be confirmed for the exact model
Control signal
To be confirmed for the exact model
Feedback
To be confirmed for the exact model
Mounting / linkage
To be confirmed for the exact model

Supply information

The quotation confirms the actual items, accessories and commercial terms for your order.

Item condition
To be confirmed in your quotation
Packaging
To be confirmed in your quotation
Included accessories
To be confirmed in your quotation
Stock confirmation
To be confirmed in your quotation
Dispatch / lead time
To be confirmed in your quotation
Price conditions
To be confirmed in your quotation
Warranty provider
To be confirmed in your quotation

More components in this catalog